Bard WA721 Specifiche Pagina 9
- Pagina / 21
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Manual 2100-425
Page 7
WALL MOUNTING INFORMATION
1. Two holes, for the supply and return air openings,
must be cut through the wall as shown in Figure 3.
2. On wood-frame walls, the wall construction must
be strong and rigid enough to carry the weight of
the unit without transmitting any unit vibration.
See Figures 4 and 5.
INSTALLATION INSTRUCTIONS
4. Mount bottom mounting bracket.
5. Hook top rain flashing under back bend of top.
Top rain flashing is shipped secured to the right
side of the back.
6. Position unit in opening and secure with 5/16 lag
bolts; use 7/8 inch diameter flat washers on the lag
bolts.
7. Secure rain flashing to wall and caulk across entire
length of top. See Figure 3.
8. For additional mounting rigidity, the return air and
supply air frames or collars can be drilled and
screwed or welded to the structural wall itself
(depending upon wall construction). Be sure to
observe required clearance if combustible wall.
9. On side by side installations, maintain a minimum
of 20 inches clearance on right side to allow access
to heat strips and control panel and to allow proper
airflow to the outdoor coil. Additional clearance
may be required to meet local or national codes.
TYPICAL INSTALLATIONS
See Figure 6 for common ways to install the wall-
mount unit.
WIRING — MAIN POWER
Refer to the unit rating plate for wire sizing
information and maximum fuse or “HACR" type
circuit breaker size. Each outdoor unit is marked with
a “Minimum Circuit Ampacity”. This means that the
field wiring used must be sized to carry that amount of
current. Depending on the installed KW of electric
heat, there may be two field power circuits required. If
this is the case, the unit serial plate will so indicate. All
models are suitable only for connection with copper
wire. Each unit and/or wiring diagram will be marked
“Use Copper Conductors Only”. These instructions
must be adhered to. Refer to the National Electrical
Code (NEC) for complete current carrying capacity
data on the various insulation grades of wiring
material. All wiring must conform to NEC and all
local codes.
The electrical data lists fuse and wire sizes (75ºC
copper) for all models, including the most commonly
used heater sizes. Also shown are the number of field
power circuits required for the various models with
heaters.
3. Concrete block walls must be thoroughly inspected
to insure that they are capable of carrying the
weight of the installing unit. See Figure 4.
MOUNTING THE UNIT
1. These units are secured by wall mounting brackets
which secure the unit to the outside wall surface at
both sides. A bottom mounting bracket is provided
for ease of installation.
2. The unit itself is suitable for “0” inch clearance,
but the supply air duct flange and the first 3 feet of
supply air duct require a minimum of 1/4 inch
clearance to combustible material. If a combustible
wall, use a minimum of 30-1/2" x 10-1/2"
dimensions for sizing. However, it is generally
recommended that a 1 inch clearance is used for
ease of installation and maintaining the required
clearance to combustible material. The supply air
opening would then be 32" x 12". See
Figures 3, 4 and 7 for details.
3. Locate and mark lag bolt locations and bottom
mounting bracket location. See Figure 4.
WARNING
Fire hazard can result if 1/4 inch clearance to
combustible materials for supply air duct is
not maintained. See Figure 3.
WARNING
Failure to provide the 1/4 inch clearance
between the supply duct and a combustible
surface for the first 3 feet of duct can result in
fire.
- Bard Manufacturing Company 1
- Bryan, Ohio 43506 1
- CONTENTS 2
- FOR MORE INFORMATION, CONTACT 3
- THESE PUBLISHERS: 3
- TABLE 1 4
- ELECTRIC HEAT TABLE 4
- FIGURE 1 5
- UNIT DIMENSIONS 5
- TABLE 2 5
- TABLE 3 6
- ELECTRICAL SPECIFICATIONS 6
- CAUTION 7
- FRESH AIR INTAKE 8
- CONDENSATE DRAIN 8
- WARNING 9
- Manual 2100-425 10
- Page 8 10
- WIRING — LOW VOLTAGE WIRING 11
- FIGURE 4 12
- WALL-MOUNTING INSTRUCTIONS 12
- FIGURE 5 12
- FIGURE 6 13
- WARNING 14
- FIGURE 8 15
- LOW VOLTAGE WIRING 15
- START UP 16
- SEQUENCE OF OPERATION 17
- COMPRESSOR CONTROL MODULE 17
- SERVICE HINTS 17
- PHASE MONITOR 18
- PRESSURE SERVICE PORTS 18
- ADJUSTMENTS 18
- TROUBLESHOOTING 19
- TABLE 12 20
- TABLE 11 20
- MAXIMUM ESP OF OPERATION 20
- ELECTRIC HEAT ONLY 20
- TABLE 13 21
- OPTIONAL ACCESSORIES 21
Prodotti e manuali riguardandi Climatizzatori a split Bard WA721
Climatizzatori a split Bard W48L23 Specifiche
(19 pagine)
(19 pagine)
Climatizzatori a split Bard WA372 Specifiche
(19 pagine)
(19 pagine)
Climatizzatori a split Bard WL423 Specifiche
(20 pagine)
(20 pagine)
Climatizzatori a split Bard WA482 Specifiche
(21 pagine)
(21 pagine)
Climatizzatori a split Bard W61A1 Manuale Utente
(12 pagine)
(12 pagine)
Climatizzatori a split Bard WGEIFM-5C Specifiche
(67 pagine)
(67 pagine)
Climatizzatori a split Bard W12A1-K Specifiche
(17 pagine)
(17 pagine)
Climatizzatori a split Bard WA4823 Specifiche
(21 pagine)
(21 pagine)
Climatizzatori a split Bard W38A1 Manuale Utente
(20 pagine)
(20 pagine)
Climatizzatori a split Bard PA13482-B Specifiche
(25 pagine)
(25 pagine)
Climatizzatori a split Bard W18A1 Manuale Utente
(16 pagine)
(16 pagine)
Climatizzatori a split Bard PA13421-A Specifiche
(23 pagine)
(23 pagine)
Climatizzatori a split Bard WA423 Specifiche
(21 pagine)
(21 pagine)
Climatizzatori a split Bard WA3S Manuale Utente
(22 pagine)
(22 pagine)
Climatizzatori a split Bard W17L1 Specifiche
(25 pagine)
(25 pagine)
Roland TMC-6 manuály
Uživatelské manuály a uživatelské příručky pro Hudební nástroje Roland TMC-6.
Poskytujeme 2 manuály pdf Roland TMC-6 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Roland TMC-6 Uživatelský manuál (32 strany)
Značka: Roland | Kategorie: Musical Instruments | Velikost: 3.45 MB |
Tabulka s obsahem
Roland TMC-6 Uživatelský manuál (32 strany)
Značka: Roland | Kategorie: Musical Instruments | Velikost: 0.72 MB |
Tabulka s obsahem
Information
32
Další produkty a příručky pro Hudební nástroje Roland
| Modely | Typ Dokumentu |
|---|---|
| TD-8 |
Uživatelský manuál
Kurzanleitung - ROLAND Germany,
224 stránky
|
| RD-300SX |
Uživatelský manuál
RD DIGITAL PIANOS [en] ,
4 stránky
|
| V-ACCORDION FR-7 |
Uživatelský manuál
Leitfaden für das ROLAND FR-7x/xb,
28 stránky
|
| KR-107 |
Uživatelský manuál
Roland KR-107 Owner`s manual,
20 stránky
|
| VS-2400CD |
Uživatelský manuál
Roland VS-2400CD Owner`s manual,
156 stránky
|
| RP401R |
Uživatelský manuál
Содержание Технические характеристики Roland RP401R,
24 stránky
|
| RD-300SX |
Uživatelský manuál
Roland RD-300SX Owner`s manual,
72 stránky
|
| SRX-12 |
Uživatelský manuál
Roland SRX-12 Owner`s manual,
16 stránky
|
| HP-307 |
Uživatelský manuál
HP-300 Series Brochure,
5 stránky
|
| HP-136 |
Uživatelský manuál
Service Notes RD-100,
16 stránky
|
| SP-404 |
Uživatelský manuál
Roland SP-404 Owner`s manual,
56 stránky
|
| TD-8 |
Uživatelský manuál
Roland TD-8 Owner`s manual,
224 stránky
|
| KR111 |
Uživatelský manuál
Changes resulting from software improvements,
2 stránky
|
| LX-10F |
Uživatelský manuál
LX-10F Bedienungsanleitung [en] ,
87 stránky
|
| VGA-3 |
Uživatelský manuál
VGA-3 Bedienungsanleitung,
36 stránky
|
| BR-900CD |
Uživatelský manuál
Roland BR-900CD Owner`s manual,
232 stránky
|
| KR-3 |
Uživatelský manuál
Roland KR-3 Owner`s manual,
64 stránky
|
| SRX-02 |
Uživatelský manuál
Thank you, and congratulations on your choice of the SRX-02,
8 stránky
|
| MT-90U |
Uživatelský manuál
1. Drücken Sie den [en] ,
70 stránky
|
| SP-606 |
Uživatelský manuál
Roland SP-606 Owner`s manual,
104 stránky
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale